How the dilution calculator works
Dilution lowers a solution's concentration by adding solvent. The amount of solute stays the same, provided none is added, lost or consumed in a reaction. The calculator uses this relationship to find one missing concentration or volume.
- 1Choose what to find. Select stock volume, final concentration, final volume or stock concentration. Enter the other three values. Stock volume means the portion you use, not the total amount available in the bottle.
- 2Check the concentration type and volumes. Use compatible concentration units, such as M and mM, or mg/mL and µg/mL. Final volume is the total finished solution, including the stock, not the amount of water added.
- 3Or choose By ratio. Enter the ratio and desired final volume, then specify whether the ratio means stock to water or stock to total solution. The results give the stock volume, estimated solvent amount and dilution factor.
The dilution formula
Use matching concentration units and matching volume units after conversion. Both concentrations must refer to the same solute.
For molarity, concentration multiplied by volume in liters gives moles of solute. Equating the amount before and after dilution gives C₁V₁ = C₂V₂. Rearrange it for the unknown you need.
| To find | Formula |
|---|---|
| Stock volume | V₁ = C₂ × V₂ ÷ C₁ |
| Final concentration | C₂ = C₁ × V₁ ÷ V₂ |
| Final volume | V₂ = C₁ × V₁ ÷ C₂ |
| Stock concentration | C₁ = C₂ × V₂ ÷ V₁ |
The solvent amount is an estimate that assumes additive volumes. The dilution factor also equals stock concentration divided by final concentration. Any matching volume units can replace mL.
Worked example: a tenfold dilution
Suppose you want 100 mL of a 0.1 M solution from a 1 M stock. Choose stock volume as the unknown and enter those three values.
- Stock volume: 0.1 × 100 ÷ 1 = 10 mL.
- Estimated solvent: 100 − 10 = 90 mL.
- Dilution factor: 100 ÷ 10 = 10.
- Preparation: measure 10 mL of stock and add the appropriate solvent until the total volume is 100 mL.
Dilution ratios: stock to water or stock to total
A tenfold dilution means one part stock in ten parts total, nominally one part stock plus nine parts solvent. One part stock plus ten parts water instead makes eleven parts total, an elevenfold dilution under the additive-volume assumption. Check which convention the label or protocol uses before entering a ratio such as 1:10.
Ratio mode uses volume parts and assumes additive volumes. Stock:total requires n ≥ 1; n = 1 gives undiluted stock.
| Stock : water | Dilution factor | Stock | Water |
|---|---|---|---|
| 1:4 | 5 | 200.00 mL | 800.00 mL |
| 1:10 | 11 | 90.91 mL | 909.09 mL |
| 1:16 | 17 | 58.82 mL | 941.18 mL |
| 1:32 | 33 | 30.30 mL | 969.70 mL |
| 1:64 | 65 | 15.38 mL | 984.62 mL |
| 1:128 | 129 | 7.75 mL | 992.25 mL |
These ratios describe the proportion of stock solution, not the concentration of an active ingredient. Finding the active ingredient's final concentration also requires the stock concentration.
Units and limits
Concentration conversions stay within a type: M with mM, or mg/mL with µg/mL. The calculator does not convert molarity to mass concentration or percent. Volume choices include microliters, milliliters, liters and U.S. fluid ounces and gallons. A U.S. gallon is about 3.785 L; a British imperial gallon is about 4.546 L, so they are not interchangeable.
A simple dilution requires C₂ ≤ C₁ and V₂ ≥ V₁. Equal concentrations require no added solvent. A higher target concentration cannot be reached by adding solvent. The method assumes the diluent contains none of the target solute.
Making the dilution
- 1Choose suitable measuring equipment. For accurate laboratory work, measure the stock with an appropriate pipette and prepare the final solution in a volumetric flask. Select equipment suited to the required precision.
- 2Use the specified solvent. Water is appropriate only when the product instructions or laboratory method call for it. A buffer or another compatible solvent may be required.
- 3Make up to the final volume. Follow the approved mixing procedure, then add solvent until the finished solution reaches the required volume and mix thoroughly. Treat V₂ − V₁ as a planning estimate, not a substitute for measuring the final volume.
Frequently asked questions
How do I calculate the stock volume needed?
Use V₁ = C₂ × V₂ ÷ C₁ after converting to matching units. V₂ is the total solution volume you want to prepare.
Does a 1:10 dilution mean adding nine or ten parts water?
If it means one part stock in ten parts total, use nominally nine parts water. If the instructions specify one part stock to ten parts water, use ten; select the matching convention in By ratio.
How much concentrate makes one gallon at 1:32?
For one U.S. gallon of finished mixture at one part concentrate to 32 parts water, the additive-volume calculation gives 128 ÷ 33 = 3.88 U.S. fl oz of concentrate and 124.12 U.S. fl oz of water. If 1:32 means one part stock in 32 parts total, use 4 U.S. fl oz of concentrate instead. These calculations use the U.S. gallon, not the imperial gallon.
Can I dilute a percentage solution with this calculator?
Yes, when both concentrations use the same supported volume-based percentage definition. Do not enter a mass percentage as though it were a volume percentage; the calculation may require solution densities.
Why is the solvent amount only an estimate?
Subtracting stock volume from final volume assumes the component volumes add directly. For accurate preparation, measure the stock and bring the finished solution to the required final volume instead.
How do serial dilution factors combine?
Multiply the factors for successive steps: two tenfold dilutions give a total factor of 100. This calculator handles one step at a time; use each step's final concentration as the next step's stock concentration.
Sources
- 1Chemistry 2e, 3.3 Molarity · OpenStax, Rice University · Accessed November 2026
- 22.5: Preparing Solutions · Chemistry LibreTexts · Accessed November 2026
- 3Serial Dilutions and Standard Plate Count · Montgomery College · Accessed November 2026
- 4NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically · National Institute of Standards and Technology · Accessed November 2026
- 5Acids - Mineral Acids · University of Illinois Urbana-Champaign, Division of Research Safety · Accessed November 2026
Results are estimates; follow the safety data sheet and consult a qualified laboratory professional before preparing hazardous solutions.