How the asphalt calculator works
The calculator multiplies paved area by finished thickness to find volume, then multiplies by compacted asphalt density and adds a waste allowance. The main result is asphalt mass, including waste, rounded to two decimal places. Optional results include gravel quantities, truckloads, total cost and cost per square foot or square meter.
Rectangles use length × width; circles use π × (diameter ÷ 2)2. Total area uses your entered area without deductions. For an irregular surface, add the areas of its sections and subtract unpaved islands before entering the total.
- 1Choose the shape and dimensions. Rectangle starts at 40 × 12 ft. Circle starts at 30 ft across, measured through its center. Total area starts at 500 ft².
- 2Enter the finished thickness. The default asphalt thickness is 3 in after rolling. Add a gravel base opens a separate thickness field, initially 6 in after compaction.
- 3Check the unit menus. The menus are linked: choosing a metric or imperial unit switches the other linked measurements and results to that system. Thickness uses inches, centimeters or millimeters.
- 4Open the optional settings. Adjust density and waste changes material assumptions. Count truckloads accepts a truck capacity. Estimate the cost opens material prices and delivery or other costs.
The asphalt tonnage formula
Net is asphalt mass before waste; Total includes the allowance. Use compacted thickness and density. US tons are short tons.
For metric calculations, divide thickness in millimeters by 1,000 to get meters. Area in m² × thickness in meters gives m³. Multiply by density in kg/m³ and the waste factor, then divide kilograms by 1,000 for tonnes.
Worked example: a 40 × 12 ft driveway
The default rectangle uses 3 in of asphalt, a density of 145 lb/ft³ and 5% extra. Gravel, truckloads and costs are initially off.
- Area: 40 × 12 = 480 ft², or 53.3 yd².
- Volume: 480 × (3 ÷ 12) = 120 ft³, or 4.44 yd³.
- Before waste: 120 × 145 = 17,400 lb, or 8.7 US tons.
- Waste allowance: 17,400 × 5 ÷ 100 = 870 lb.
- Including waste: 17,400 + 870 = 18,270 lb. Dividing by 2,000 gives 9.135 US tons, displayed as 9.14 US tons.
The ordering note rounds asphalt and gravel separately: upward in half-ton or half-tonne increments, or 10 lb or 10 kg increments for quantities below one ton or tonne. Costs and truckloads use the unrounded calculated masses, not these ordering suggestions.
Compare asphalt quantities by thickness
The live Asphalt by thickness table keeps your area, density and waste setting constant. Volume excludes waste; asphalt mass includes it. These are its results for the default driveway.
| Compacted thickness | Volume | Asphalt |
|---|---|---|
| 1.5 in | 2.22 yd³ | 4.57 tons |
| 2 in | 2.96 yd³ | 6.09 tons |
| 2.5 in | 3.70 yd³ | 7.61 tons |
| 3 inDefault | 4.44 yd³ | 9.14 tons |
| 4 in | 5.93 yd³ | 12.18 tons |
| 6 in | 8.89 yd³ | 18.27 tons |
Metric mode compares 40, 50, 60, 75, 100 and 150 mm. Those depths are not exact conversions of the inch rows.
Density and waste assumptions
With Adjust density and waste off, asphalt density is 145 lb/ft³ in imperial mode or 2,325 kg/m³ in metric mode. Gravel uses 139 lb/ft³ or 2,225 kg/m³. FHWA's estimating table lists those metric values; the calculator's imperial presets are rounded independently, so switching systems can slightly change the calculated mass.
Switch the setting on to enter supplier-specific densities and a waste allowance from 0% to 50%. The same allowance applies to asphalt and gravel. The default 5% is a planning allowance for low spots, edges and handling losses, not a separate compaction factor.
At 145 lb/ft³, each inch of compacted thickness weighs 108.75 lb/yd² before waste. Michigan DOT uses a rounded reference rate of 110 lb/yd² per inch.
Choosing compacted asphalt thickness
Loose mix is placed thicker so rolling can bring it to the specified finished depth. The Asphalt Paving Handbook distinguishes these loose and compacted thicknesses. Because this calculator uses finished volume and compacted density, do not add another compaction multiplier.
The Colorado Asphalt Pavement Association's March 2020 brief gives the residential minimum sections below for cars, light trucks and occasional heavier service vehicles. It describes a 1.5–2 in overlay as typical after weak spots, holes and large cracks are repaired. These regional recommendations do not establish the design for every soil condition or traffic load.
| Subgrade support | Full-depth asphalt | Asphalt over aggregate base |
|---|---|---|
| Poor | 5.5 in | 3 in over 6 in |
| Fair | 4.5 in | 3 in over 4 in |
| Good | 4.5 in | 3 in over 4 in |
Gravel base and truckloads
Add a gravel base uses the same footprint as the asphalt. Base volume equals area × compacted base thickness; its mass uses the base density and the same waste percentage. A 6 in base under the default driveway is 240 ft³, or 8.89 yd³. Including 5% extra, it weighs 17.51 US tons, with an ordering suggestion of 18.0 tons.
Count truckloads divides each material's mass by the entered capacity and rounds up separately to whole loads. One capacity applies to both materials. At the default 15 US tons per truck, this example needs one asphalt load and two gravel loads; the final load can be partial.
Material costs and cost per area
Estimate the cost accepts asphalt and gravel prices per US ton or metric tonne, plus one delivery and other costs amount. Each material cost is its unrounded mass including waste × its price. The total adds the supplied costs; cost per area divides that total by the paved area.
Enter at least one material price for cost results to appear. Blank prices are omitted, so a displayed total can be partial; entering delivery costs alone does not display a total. Labor, excavation, taxes and equipment are not automatically added.
For illustration, price the example's asphalt at $100 per US ton, gravel at $30 per US ton and other costs at $200. Asphalt costs $913.50 and gravel costs $525.42. The total is $1,638.92, or $3.41/ft².
Check before ordering
- 1Separate different depths. Run separate calculations for sections with different asphalt or base thicknesses, then add their material quantities.
- 2Check the base footprint. The gravel calculation does not automatically extend beyond the asphalt edges. Calculate any wider base area separately.
- 3Confirm supplier details. Recheck custom densities after changing unit systems, match the quoted price unit and confirm the truck's actual carrying capacity.
Frequently asked questions
How many square feet does a ton of asphalt cover?
At 145 lb/ft³, one US ton covers about 83 ft² at 2 in thick or 55 ft² at 3 in thick, before waste. Adding a waste allowance reduces the area that the same purchased tonnage can cover.
How much does a cubic yard of asphalt weigh?
At the calculator's imperial default, 27 ft³ × 145 lb/ft³ = 3,915 lb, or 1.96 US tons. This is compacted asphalt before the waste allowance.
What is the difference between a ton and a tonne?
A US short ton is 2,000 lb, about 907.18 kg. A metric tonne is 1,000 kg, about 2,204.62 lb, so prices per ton and per tonne cannot be used interchangeably.
Can I use the calculator for an asphalt overlay?
Yes. Enter only the new compacted asphalt thickness, and leave the gravel base off unless you are adding one. The calculator does not work out milling, patching or tack coat quantities.
Sources
- 1Application Rates and Weights for Estimating Purposes · Federal Highway Administration · Accessed November 2026
- 2Asphalt Driveways: Technical Brief, March 2020 · Colorado Asphalt Pavement Association · Accessed November 2026
- 3501: Plant Produced Hot Mix Asphalt · Michigan Department of Transportation · Accessed November 2026
- 4Asphalt Paving Handbook, 7.5: Layer Thickness · National Asphalt Pavement Association · Accessed November 2026
- 5NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically · National Institute of Standards and Technology · Accessed November 2026
Quantity and cost estimates do not replace pavement design; confirm thickness, mix density and orders with your paving contractor.