How the tile calculator works
The calculator estimates rectangular tile quantities for a floor, wall or backsplash, or an area you already know. It subtracts any area you leave out, allows for grout joints, adds 10% for cuts by default, then rounds up to whole tiles. Optional switches show boxes, grout and material costs.
Choose Floor for length × width, Wall or backsplash for width × height, or Total area for a combined measurement. For an irregular room, add the areas of smaller rectangles before entering the total. Leave out an area works in all three modes.
The tile quantity formula
The same subtraction works in m². The deduction is zero while its switch is off, and must be smaller than gross area when enabled.
Enter the tile's actual length and width without adding the joint yourself. The calculator adds one joint width to each dimension to form a repeating tile module. That module includes grout space; it is not the tile's face area.
Use matching length units, with A and M in the corresponding square units. Ceiling brackets mean round up. The tiny subtraction prevents numerical noise from adding a tile.
A grout joint is included even when Work out the grout is off. The initial inch setting uses 1/8 in joints. Enable that switch to change joint width; disabling it hides the controls and grout quantity but does not remove joint spacing. Change the extra for cuts lets you replace the default 10% with any allowance from 0% to 50%.
Worked example: a 12 × 10 ft floor
The default floor is 12 × 10 ft, with tiles measuring 24 × 12 in, 1/8 in joints and 10% extra. No area is left out, and boxes, grout quantities and costs are initially off.
- Floor area: 12 × 10 = 120 ft².
- Tile module: (24 + 0.125) × (12 + 0.125) ÷ 144 = about 2.031 ft².
- Tiles before extra: 120 ÷ the unrounded module area = 59.07.
- With 10% extra, the unrounded tile requirement becomes about 64.98, rounded up to 65 tiles.
- Tile face area to buy: 65 × 2 = 130 ft².
Extra for cuts shows 10% · 5 tiles. That count compares 65 tiles with the rounded zero-extra requirement of 60 tiles, rather than rounding 10% of 60 separately.
| Extra | Tiles | Tile face area |
|---|---|---|
| 0% | 60 | 120 ft² |
| 5% | 63 | 126 ft² |
| 10%Default | 65 | 130 ft² |
| 15% | 68 | 136 ft² |
| 20% | 71 | 142 ft² |
The calculator displays this five-row comparison when Change the extra for cuts is enabled. Its comparison runs from 0% to 20%, even if your chosen allowance is higher.
Grout joints and grout quantity
Work out the grout reveals joint width and tile thickness. Inch defaults are 1/8 in and 3/8 in; metric defaults are 3 mm and 10 mm. These menus keep separate presets, not exact conversions, so review them after changing unit systems.
| Setting | Inch choices | Metric choices |
|---|---|---|
| Joint width | 1/16, 1/8, 3/16, 1/4 in | 2, 3, 5, 8 mm |
| Tile thickness | 1/4, 5/16, 3/8, 1/2 in | 6, 8, 10, 12 mm |
Choose a joint suitable for your tile instead of simply selecting the smallest option. The Tile Council of North America explains that tile-size variation and edge shape affect the appropriate joint width.
For this equation, area is in m² and every tile and joint dimension is in mm. The fixed 1.6 consumption factor follows the form published in MAPEI's Keracolor GG data sheet; 1.10 adds a separate 10% grout allowance.
Grout uses net tiled area, not the extra tile purchase. Its 10% allowance does not change with your cut allowance. Enabling grout for the default floor gives about 6.4 lb and suggests one 10 lb bag.
The calculator suggests one 10 lb bag for quantities up to 10 lb, otherwise whole 25 lb bags. Metric suggestions use one 5 kg bag up to 5 kg, otherwise whole 20 kg bags. These are fixed packaging assumptions; check your chosen grout's coverage and pack sizes.
Whole boxes and material costs
Enable Count boxes and enter Tiles per box, initially eight. Boxes equal the tile count divided by tiles per box, rounded up. The default example therefore needs nine boxes containing 72 tiles. The main result remains 65 tiles, and Tile to buy, by area remains 130 ft²; neither includes the additional tiles from box rounding.
Estimate the cost accepts a tile price per ft², m² or yd², plus optional Grout, adhesive and other costs. Tile cost equals purchased tile face area × unit price. With boxes enabled, purchased tile face area uses every tile in those boxes; otherwise it uses the main tile count.
For example, nine boxes of eight default-size tiles contain 144 ft² of tile faces. At an illustrative $4 per ft², tile cost is $576. Add $60 of other costs for a $636 total, or $5.30 per ft² tiled: $636 ÷ the net 120 ft².
Cost per area includes supplied other costs and divides by net tiled area. A tile price is required for any cost result; other costs alone produce none. Grout quantities do not automatically generate a price, and labor, tax or delivery are included only if you enter them.
Check the measurements before ordering
- 1Measure the actual tile. Nominal sizes can differ from actual face dimensions. Enter positive surface and tile dimensions; use the unit menus to convert linked measurements between metric and imperial. The tile-price unit menu can be changed independently.
- 2Deduct only untiled areas. Add together openings, cabinets or other spaces you will not tile. If your Total area already excludes them, do not deduct them again.
- 3Check the cuts and matching cartons. The area calculation does not optimize cut-piece reuse or count rows around obstacles. Match carton shade and caliber markings, as Marazzi advises. Daltile also recommends keeping extra tile for future replacements.
Frequently asked questions
How much extra should I allow for diagonal or herringbone tile?
The calculator's guidance suggests about 10% for straight layouts, 15% for diagonal layouts and 15%–20% for herringbone. These are planning allowances, not automatic pattern calculations. Enable Change the extra for cuts and enter the allowance your layout needs.
Does rotating a rectangular tile change the count?
Swapping tile length and width does not change the calculated module area or tile count. It can change the actual cuts at the edges, so check the proposed orientation before ordering.
Can I use this for hexagonal tiles or mosaic sheets?
The count formula assumes rectangular tile faces, so it does not directly model hexagons or other nonrectangular shapes. Mosaic-sheet dimensions also do not describe the individual joints needed for the grout formula. Use the supplier's sheet coverage and product-specific grout guidance for those purchases.
What if the box lists coverage instead of a tile count?
Count boxes requires the number of tiles per box, not box coverage. Find the piece count on the packaging or ask the supplier, then compare the calculated purchase with the manufacturer's stated carton coverage.
Sources
- 1Grout · Tile Council of North America · Accessed November 2026
- 2Keracolor GG technical data sheet · MAPEI · Accessed November 2026
- 3Tile and natural stone FAQs · Daltile · Accessed November 2026
- 4Frequently asked questions · Marazzi USA · Accessed November 2026
- 5Choice Twilight Grey 12X24 Matte: product details · Daltile · Accessed November 2026
Material quantities and costs are estimates; confirm your order with your tile supplier or installer.