How the ring size calculator works
The calculator estimates ring size from a finger measurement, an existing ring or a size you already know. It shows approximate US/Canada, UK, EU/ISO and Japanese sizes, together with the inside diameter and circumference. Choose which sizing system appears first, then check the working and nearby sizes.
- 1Measure your finger. Choose Finger. Wrap a narrow paper strip around the base of the intended finger without squeezing it, mark the overlap and measure the length to the mark. Enter that circumference in millimeters or inches.
- 2Measure a ring that fits. Choose A ring. Measure straight through the center of the opening, from one inside edge to the opposite inside edge. Enter this inside diameter, without including the metal.
- 3Match a ring on screen. Choose On screen. First adjust the calibration bar to match the short edge of a standard bank card. Then adjust the reference circle until it matches the inside opening of a ring that fits.
- 4Convert a known size. Choose Convert, select the original sizing system and enter the size. The calculator converts that size through its nominal inside measurements before finding equivalents in the other systems.
Keep circumference and diameter separate: circumference measures around the opening, while diameter measures across it. The nearest-size results and chart here use half-size steps for US and UK sizes, and whole-number steps for EU and Japanese sizes. Between-size measurements can also be compared with the neighboring sizes shown.
The ring size formulas
For a circular opening, circumference and diameter are linked by π. Measurements entered in inches are multiplied by 25.4 to obtain millimeters. The calculation keeps unrounded measurements until the final size labels and displayed dimensions are produced.
Both measurements refer to the inside opening of the ring.
US and Canadian sizes
The US conversion uses a conventional diameter of 0.458 inches at size 0, increasing by 0.032 inches per whole size. Those values become 11.6332 mm and 0.8128 mm. IKOHE's published inch chart follows this sequence through the sizes used in the comparison below.
Round the calculated US size to the nearest half size for the displayed equivalent.
UK, European and Japanese sizes
The UK letter convention used here starts at A = 37.5 mm circumference. Each full letter adds 1.25 mm, and a half letter adds 0.625 mm. Count A as zero steps, B as one and C as two, then round the calculated number of steps to the nearest half.
For example, 13 steps after A is N; 13.5 steps is N½.
The EU/ISO size is the inside circumference in millimeters rounded to the nearest whole millimeter. ISO 8653 specifies this designation, so a 54 mm inside circumference is size 54. The EU label here means this circumference-based system; do not assume every European retailer uses that numbering.
Japan uses more than one sizing convention. This calculator's Japan result follows the customary JCS scale shown by NIWAKA: size 1 has a 13 mm inside diameter, and each additional size adds one-third of a millimeter. It does not treat the Japanese size as circumference minus 40.
Round to the nearest whole JCS size. To reverse the conversion, diameter in millimeters equals (Japan size + 38) ÷ 3.
Worked example: 54.4 mm around the finger
Suppose your paper strip measures 54.4 mm. Dividing by π gives an inside diameter of 17.32 mm. The unrounded US calculation is about 6.99, which rounds to US 7; the UK calculation gives 13.52 letter steps after A, which rounds to N½. The circumference rounds to EU 54, and the Japanese calculation gives about 13.95, which rounds to JCS 14.
Entering US 7 in Convert gives a nominal diameter of 17.32 mm and circumference of 54.42 mm. That is close to the finger measurement, but not identical. A rounded size label describes a nominal size, not every measurement that rounds to it.
Ring size comparison chart
Each row starts with a US size and calculates its dimensions using the US formula above. The other size labels are the nearest equivalents under this page's conventions. Diameter is displayed to two decimal places and circumference to one; the conversions use the unrounded values.
| US | UK | EU/ISO | Japan, JCS | Diameter (mm) | Circumference (mm) |
|---|---|---|---|---|---|
| 4 | H½ | 47 | 7 | 14.88 | 46.8 |
| 5 | J½ | 49 | 9 | 15.70 | 49.3 |
| 6 | L½ | 52 | 12 | 16.51 | 51.9 |
| 7Example size | N½ | 54 | 14 | 17.32 | 54.4 |
| 8 | P½ | 57 | 16 | 18.14 | 57.0 |
| 9 | R½ | 60 | 19 | 18.95 | 59.5 |
| 10 | T½ | 62 | 21 | 19.76 | 62.1 |
Get a more useful measurement
- 1Measure the intended finger. Use the finger and hand that will wear the ring. When borrowing an existing ring, choose one worn on that same finger.
- 2Check under normal conditions. Repeat the measurement with comfortably warm hands. GIA notes that temperature and time of day can change finger size, so a single measurement may not describe your usual fit.
- 3Check the knuckle and band width. The ring must pass over the knuckle and remain secure at the base. Wide bands fit more snugly, so try a sizing band of similar width instead of adding a fixed allowance automatically.
- 4Keep the screen calibration unchanged. The calibration uses the 53.98 mm short edge of an ID-1 card, whose nominal dimensions are 85.60 × 53.98 mm. Recalibrate after changing browser zoom or moving to another display, then match the ring's inside opening again.
Frequently asked questions
What ring size is a 17 mm inside diameter?
Using this page's formulas, 17 mm gives an unrounded US size of about 6.60, so the nearest half size is US 6½. Its circumference is 53.41 mm, giving approximately UK M½, EU 53 and Japanese JCS 13.
What is a US size 7 in UK, EU and Japanese sizes?
Under the conventions used here, US 7 converts to approximately UK N½, EU 54 and Japanese JCS 14. Its nominal inside diameter is 17.32 mm and circumference is 54.42 mm; a retailer's chart may assign a different neighboring label.
Are UK and European ring sizes the same?
No. The UK result uses letters, while the EU/ISO result uses inside circumference in millimeters rounded to a whole number. Select the system named by the seller instead of treating the numbers and letters as interchangeable.
How accurate is the on-screen ring sizer?
It depends on how closely you match the calibration bar and ring opening. The calculator uses a known card dimension to establish screen scale; it cannot correct an inaccurate visual match. Recheck the calibration after zooming or changing displays.
Why can converting a size back give a different result?
The sizing systems use different increments, so rounding loses some measurement information. Several nearby measurements can produce the same size label, and converting that label back uses its nominal measurement. Keep the original diameter or circumference when comparing charts.
Sources
- 1ISO 8653:2016: Jewellery, ring-sizes, definition, measurement and designation · International Organization for Standardization · Accessed November 2026
- 2IKOHE tools catalog: Ring sizes to inches · IKOHE · Accessed November 2026
- 3AU ring size chart in mm and casting shrinkage · 3D Werk · Accessed November 2026
- 4Japanese ring size guide · NIWAKA · Accessed November 2026
- 5How to determine ring size: Tips and ring size chart · Gemological Institute of America · Accessed November 2026
- 6Doc 9303, Part 5: Specifications for TD1 size machine readable official travel documents · International Civil Aviation Organization · Accessed November 2026