How to use the deck stain calculator
Enter the size of the deck, the number of coats and the condition of the wood. That's enough for a deck with no railings or stairs. Switch on the parts your deck has, and the calculator measures their wood too.
- 1Measure the deck. Multiply the length by the width of the floor, or enter the total area if you know it. Add another section covers an L-shaped deck, a landing or a second level. Every box has a unit menu: pick meters or centimeters in any of them, and every box and the result switch to metric.
- 2Pick the coats and the wood. Choose Rough or weathered for rough-sawn, gray or old boards: they soak up more stain.
- 3Switch on railings and stairs. Add railings takes the total railing length, its height and its style. Add stairs takes the number of steps, the stair width and whether the risers are closed.
- 4Check the coverage and buy. The calculator uses typical coverage unless you switch on Use the coverage on the can and enter the label's figures. Pick a can size to see how many to buy, and switch on Estimate the cost to add a price.
How much stain a deck needs
Stain is used by area, so the calculator adds up every surface you'll stain: the deck boards, the railings and the stairs. It then divides that area by the coverage of each coat. A second coat covers more than the first, because the wood soaks up less once the first coat is in it, so two coats take less than twice the stain of one.
Coverage is in square feet per gallon. For rough or weathered wood, both coverages are multiplied by 0.6.
With the default numbers, a 16 × 12 ft deck has 192 ft² of boards. The first coat at 250 ft² per gallon takes 192 ÷ 250 = 0.77 gallons, and the second coat at 300 ft² per gallon takes 192 ÷ 300 = 0.64 gallons, so 1.41 gallons in all: one gallon and two quarts.
Coverage: smooth or rough wood, first or second coat
Coverage is printed on the can, and it changes with the wood. Labels often give one figure for smooth wood and a lower one for rough wood, and some give a higher figure for the second coat. Two examples:
| Product | Coverage per gallon | What it shows |
|---|---|---|
| Cabot Gold | 1st coat: 250–350 ft²; 2nd coat: 300–400 ft² | The second coat covers more |
| Duckback SuperDeck semi-transparent | Smooth: 275–375 ft²; rough: 175–225 ft² | Rough wood covers about 40% less |
Unless you enter your own figures, the calculator uses 250 ft² per gallon for the first coat and 300 for the second, the low ends of the Cabot ranges, so a smooth deck shouldn't run short. Rough or weathered multiplies both by 0.6, close to the Duckback figures. If your can lists separate figures, switch on Use the coverage on the can and enter the smooth-wood ones; the Wood choice still handles rough boards.
Railings: more wood than you'd think
A railing is a lot of narrow pieces, and stain goes on every face. The 2021 International Residential Code requires deck guards to be at least 36 in high, with no opening a 4 in sphere can pass through, which in practice means balusters roughly 5 in apart. For a baluster railing, the calculator counts these parts, all faces:
| Part | Assumed size | For 40 ft of 36 in railing |
|---|---|---|
| Posts | 4×4 (3.5 in), at most 6 ft apart | 8 posts: 28 ft² |
| Cap | 2×6 on top (5.5 × 1.5 in) | 47 ft² |
| Top and bottom rails | 2×4 (3.5 × 1.5 in) | 67 ft² |
| Balusters | 2×2 (1.5 in), 5 in apart, 31 in long | 96 balusters: 124 ft² |
| Total | 265 ft², about 6.6 ft² per foot |
That's more than many quick rules allow, such as 3 ft² per foot of railing, and on a small deck the railing can take more stain than the floor. For a railing of solid boards or panels, the calculator counts both faces of the boards plus the posts and cap. For cable or glass railings, only the wooden posts and cap get stain. Include stair railings in the railing length.
Stairs
For each step, the calculator counts the tread and its front edge, the outer face of the two stringers along the slope, and the riser if the risers are closed. It assumes a typical deck stair: treads of two 2×6 boards (11 in deep), a 7.5 in rise and a 10.5 in run, within the code's limits of a 7¾ in maximum riser and a 10 in minimum tread. Four steps 4 ft wide with open risers come to about 25 ft².
One coat or two?
New or bare wood, and stains that call for it, need two coats; Cabot Gold, for example, says two coats are required. A deck whose stain is still in good shape often needs only one fresh coat. Follow the label for the time between coats: some stains go on wet-on-wet, others need the first coat to dry.
Penetrating stains only soak in so far. Brush out puddles and wipe up any stain that stays on the surface, because what doesn't soak in can stay tacky and wear badly.
Buying and using the stain
Deck stain is sold in quarts, gallons and five-gallon buckets in the U.S., and in 1, 2.5 and 5 liter cans elsewhere. A U.S. gallon is 3.785 liters and a quart is 0.946 liters. Pick the size you'll buy: the calculator rounds up to whole cans and shows the leftover. When one or two quarts finish the job, it says so, since that's cheaper than another gallon.
If the job takes more than one can, mix them together in a larger bucket before you start, as Cabot's instructions say, so the color stays even across the deck. Keep the leftover for touch-ups on steps and high-traffic spots.
Frequently asked questions
How much stain do I need for a 12 × 16 deck?
About 1.4 gallons for two coats on smooth boards: 192 ft² ÷ 250 = 0.77 gallons for the first coat and 192 ÷ 300 = 0.64 for the second. Buy one gallon and two quarts, or two gallons. Railings and stairs come on top.
How much stain do I need for a 20 × 20 deck?
About 2.9 gallons for two coats on smooth boards: 400 ft² ÷ 250 = 1.6 gallons plus 400 ÷ 300 = 1.33 gallons. Three gallons cover it. On rough or weathered wood, plan on about 4.9 gallons.
How many square feet does a gallon of deck stain cover?
Usually about 250 to 375 ft² for a first coat on smooth wood, and less on rough or weathered boards: Duckback lists 175 to 225 ft² for rough surfaces. The second coat covers more, for example 300 to 400 ft² for Cabot Gold.
How much stain do deck railings need?
Counting every face of the posts, rails, cap and balusters, a 36 in baluster railing has about 6.6 ft² of wood per foot. 40 ft of railing is about 265 ft², more than many small decks.
Does a second coat take as much stain as the first?
No. The wood soaks up less the second time, so the second coat covers more area per gallon. Two coats usually take about 1.8 times the stain of one, not twice as much.
How much stain do deck stairs take?
About 6 ft² per step for a 4 ft wide stair with open risers, counting the tread, its edge and the stringers. Closed risers add about 2.5 ft² per step.
Sources
- 1Cabot Gold specification sheet · Cabot · Accessed November 2026
- 2Duckback SuperDeck Semi-Transparent Exterior Stain (product listing) · True Value · Accessed November 2026
- 32021 International Residential Code, Chapter 3: Building Planning (R311.7 Stairways, R312 Guards) · International Code Council · Accessed November 2026
- 4NIST Guide to the SI, Appendix B.8: Factors for units listed alphabetically · National Institute of Standards and Technology · Accessed November 2026