How the paint calculator works
The calculator finds the area you will paint, multiplies it by the number of coats, then divides by coverage per gallon or liter. Surface and touch-up allowances increase that quantity. The main result is finish paint only; primer appears separately.
Every box and the result have their own unit menu. Picking a metric unit in any of them switches the whole calculator to meters and liters; an imperial one switches it back to feet and gallons. Results include whole cans to buy, estimated paint left over and optional material costs. Walls and ceilings have separate can counts, while the comparison table shows purchases for one, two or three coats.
Enter the surfaces you will paint
- 1Choose a measuring method. Whole room uses a rectangular room's length, width and wall height. Wall by wall accepts the width and height of one to six rectangular walls. Total area accepts a one-coat area with openings already deducted.
- 2Subtract unpainted areas. In Whole room and Wall by wall, switch on Take off doors or Take off windows, then enter how many there are and their dimensions. One door size applies to every door, and one window size applies to every window. Switch on Take off other areas for cabinets, tile or a fireplace. Nothing is subtracted while a switch is off.
- 3Include the ceiling if needed. Switch on Paint the ceiling. Whole room calculates ceiling area as length × width. The other methods need a separate ceiling area. In Total area mode, leave the ceiling out of the entered wall area if you also enable the ceiling option.
- 4Set paint and purchasing details. Choose one, two or three coats and a can size. Switch on Adjust coverage and surface to enter your can's coverage, a surface type or touch-up extra; while it's off, the calculator uses 350 ft² per gallon on a smooth surface. Switch on primer if needed, and Estimate the cost to enter prices per can.
For differently sized openings, calculate their combined area yourself and enter it under Take off other areas, with Take off doors and Take off windows switched off. Total deductions must be smaller than gross wall area. The Wall by wall table shows each wall's dimensions and gross area before these shared deductions.
The paint quantity formula
For a rectangular room. Wall by wall instead adds each width × height. Total area uses your entered net area directly. Ceiling area is added separately.
Use the equation separately for walls and ceiling, then add their paint quantities. With area in m² and coverage in m²/L, the result is liters.
The surface factor is 1 for Smooth, 1.15 for Textured and 1.40 for Rough or porous. Extra for touch-ups ranges from 0% to 50% and multiplies the surface allowance. For example, Textured with 10% extra uses 1.15 × 1.10 = 1.265, or 26.5% more paint than the unadjusted estimate.
Worked example: a 12 × 12 ft room
This example uses the default 12 × 12 ft room with 8 ft walls, with Take off doors and Take off windows switched on at their default sizes: one 36 × 80 in door and two 36 × 60 in windows. The surface is smooth, coverage is 350 ft² per gallon and two coats are selected. Ceiling paint, primer and touch-up extra are off; can size is one gallon. With nothing subtracted, the same room needs 384 × 2 ÷ 350 = 2.19 gal.
- Gross walls: 2 × (12 + 12) × 8 = 384 ft².
- Openings: 20 ft² for the door plus 30 ft² for the windows = 50 ft².
- Net walls: 384 − 50 = 334 ft².
- Paint: 334 × 2 ÷ 350 = 1.91 gal.
- Purchase: two one-gallon cans, leaving an estimated 0.09 gal.
| Coats | Paint needed | Cans to buy | Left over |
|---|---|---|---|
| 1 | 0.95 gal | 1 | 0.05 gal |
| 2Default | 1.91 gal | 2 | 0.09 gal |
| 3 | 2.86 gal | 3 | 0.14 gal |
Switching on the ceiling adds 144 ft² and 0.82 gal for two coats. The combined result becomes 2.73 gal: two gallon cans for the walls and one for the ceiling, with 0.27 gal left over in total.
Coverage, surface allowances and primer
Enter coverage for one coat from the can or product data sheet. Sherwin-Williams gives a typical paint range of 350–400 ft² per gallon, approximately 8.6–9.8 m²/L. The calculator defaults to 350 ft² per gallon; that does not guarantee the same coverage on every surface.
Textured adds 15% to paint quantity; Rough or porous adds 40%. These are calculator planning allowances, not product-specific coverage ratings. If your entered coverage already accounts for the actual texture or porosity, select Smooth to avoid applying another allowance.
Primer requirements depend on the coating and substrate. For example, BEHR PREMIUM PLUS directions specify a separate suitable primer for stain-blocking or over oil-based or glossy surfaces. Check the product instructions before deciding whether a separate primer is needed.
Sherwin-Williams gives a general primer range of 200–300 ft² per gallon. The calculator starts at 250 ft² per gallon, approximately 6.1 m²/L; replace this with your primer's coverage.
Enabling primer adds one coat over all included walls and ceiling, using the same surface and touch-up allowances. Finish-coat count does not multiply primer. For the default walls, 334 ÷ 250 = 1.34 gal, requiring two gallon cans of primer. Spot priming needs a separate calculation using only the area being primed.
Cans, leftovers and material costs
The feet-and-gallons setting uses U.S. liquid gallons, not British imperial gallons. One U.S. gallon is about 3.785 L, and one U.S. quart is about 0.946 L.
Choose quart, gallon or five-gallon containers, or metric cans of 1, 2.5, 5 or 10 L. Each quantity is divided by the selected can size and rounded up. Wall and ceiling paint are rounded separately; primer is rounded once for their combined area.
Only one container size is used per run. Choosing Quart expresses the entire purchase in quarts, not just the remainder after gallon cans. With gallon cans and walls only, when one or two quarts would finish the job, the result also suggests that mix, such as 2 gallons and 1 quart for 2.19 gal; costs still use whole cans of the selected size. Paint left over means purchased finish-paint volume minus the estimate, including allowances; primer leftovers are not shown.
Switch on Estimate the cost to enter prices; they apply per selected can. Total cost adds paint and primer purchases only where prices are supplied. If one price is missing, that product contributes nothing to the displayed cost, so the total is partial. Cost per ft² or m² divides this cost by the net wall-plus-ceiling area once, not by area multiplied by coats.
Check the estimate before buying
- 1Separate different paint products. Walls and ceiling share coverage, coats, surface setting and paint price. Run separate estimates if these differ, or if individual walls need different colors.
- 2Check unusual shapes. For sloped walls or vaulted ceilings, calculate the actual surface area first and use Total area or the separate Ceiling area input.
- 3Budget for other supplies. The cost does not automatically add labor, tax, brushes, rollers, tape or preparation materials.
Frequently asked questions
How much paint do I need for a 12 × 12 room?
With 8 ft walls, one default-size door and two default-size windows, the calculator estimates 1.91 gal for two coats at 350 ft² per gallon. Buy two gallon cans for the walls. Including the ceiling raises the estimate to 2.73 gal and the purchase to three gallon cans.
How much paint does an accent wall need?
A 12 × 8 ft wall without openings has 96 ft². At two coats and 350 ft² per gallon, it needs 0.55 gal, rounded up to three quarts or one gallon. In Wall by wall mode, leave Take off doors and Take off windows switched off unless that wall has openings.
Should I subtract doors and windows in Total area mode?
Yes, subtract them before entering the area. Total area mode makes no further opening deductions. In the other two measuring modes, switch on Take off doors or Take off windows and enter their counts and dimensions for automatic deductions.
Does the main paint result include primer?
No, it shows finish paint only. When enabled, primer appears in a separate row with its own one-coat quantity and can count.
Does the ceiling use different coverage or coats?
No, the ceiling shares the wall settings for coverage, coats, surface allowance and touch-up extra. Its paint quantity and can count are shown separately. Use separate runs when ceiling paint has different specifications.
Why does changing can size change cost but not paint needed?
Paint needed comes from area, coats, coverage and allowances. Can size changes the rounded purchase quantity and leftovers. Update Price per can whenever you change container size.
Sources
- 1BEHR PREMIUM PLUS Interior Eggshell Enamel · Behr Paint Company · Accessed November 2026
- 2NIST Guide to the SI, Appendix B.8: Factors for Units Listed Alphabetically · National Institute of Standards and Technology · Accessed November 2026
- 3Lead-Safe Renovations for DIYers · U.S. Environmental Protection Agency · Accessed November 2026
Paint quantities and material costs are estimates; follow the product label for coverage, preparation and safe use.