How the gear ratio calculator works
The calculator uses driven teeth ÷ driving teeth as its gear ratio convention. A larger reduction lowers output speed and increases ideal output torque. Gears mode works from tooth counts for one or more stages; Vehicle mode connects engine RPM and road speed through the transmission, axle and tires.
- 1Choose gears or a vehicle. Use Gears for meshing gear pairs. Use Vehicle to find engine RPM at a road speed, or road speed at an engine RPM.
- 2Enter the driving and driven gears. Enter positive whole-number tooth counts, with the driving gear first. Add stages for a compound train. Input RPM and input torque are optional: tooth counts alone determine the ratio, while each optional input enables its corresponding output.
- 3Supply the vehicle gearing and tires. Enter the axle ratio, transmission gear ratio and tire size or overall tire diameter. Supply road speed to find RPM, or RPM to find speed. A direct transmission gear is 1.00; an overdrive gear is below 1.00.
Gear ratio, output speed and torque formulas
Use matching input and output torque units, such as N·m. The ratio and speed are magnitudes; rotation direction is handled separately.
Efficiency applies to the whole entered train. If omitted, it is treated as 100%, an ideal assumption. At a specified input RPM, efficiency reduces calculated output torque, not the tooth-count speed ratio. A 1:1 pair therefore has equal speed magnitudes but can still lose torque through friction.
Worked example: 20 teeth driving 60 teeth
Take a 20-tooth driving gear and a 60-tooth driven gear, with an input speed of 1,200 RPM, input torque of 10 N·m and overall efficiency of 90%.
- Gear ratio: 60 ÷ 20 = 3, written 3:1.
- Output speed: 1,200 ÷ 3 = 400 RPM.
- Output torque: 10 × 3 × 0.90 = 27 N·m.
- Direction: one external mesh makes the driven gear turn opposite to the driving gear.
| Driving → driven | Ratio | Output speed | Ideal torque |
|---|---|---|---|
| 20 → 60 teeth | 3:1 | 400 RPM | 30 N·m |
| 30 → 30 teeth | 1:1 | 1,200 RPM | 10 N·m |
| 40 → 20 teeth | 0.5:1 | 2,400 RPM | 5 N·m |
Compound trains, idlers and rotation direction
For a compound train, multiply the stage ratios. With 12 teeth driving 40, followed by 15 driving 45, the 40-tooth and 15-tooth gears are fixed to the same intermediate shaft. The overall ratio is (40 ÷ 12) × (45 ÷ 15) = 10:1. An input of 1,750 RPM therefore produces 175 RPM.
An idler is different: the same intermediate gear receives and passes on motion. Its tooth count cancels from the overall ratio. Each external mesh reverses rotation, so an odd number of meshes gives opposite rotation and an even number gives the same rotation, viewed from the same end of parallel shafts. Adding an idler changes this count without changing the ratio, though it adds another potential loss.
This direction rule is for external gears on parallel shafts. Internal gears, worm drives and planetary arrangements need their own direction or relative-motion analysis.
Vehicle engine RPM and road speed
Vehicle mode multiplies the transmission gear ratio by the axle ratio. Engine RPM divided by that combined ratio gives wheel RPM. Multiplying wheel RPM by tire circumference then gives road speed, assuming no slip.
These equations use road speed in mph and overall tire diameter in inches. They assume the selected gear is engaged with no clutch or torque-converter slip.
There are 63,360 inches in a mile and 60 minutes in an hour, giving 63,360 ÷ 60 = 1,056. Dividing by π produces the familiar rounded constant 336.14. With speed in km/h and tire diameter in millimeters, the equivalent rounded constant is 5,305.16. Calculations should retain full precision until the result is displayed.
At 65 mph with a 3.73 axle, a 1.00 transmission gear and 31-inch tires, engine speed is 65 × 3.73 × 1.00 × 1,056 ÷ (π × 31), or approximately 2,629 RPM.
Finding diameter from tire size
In 265/70R17, 265 is the nominal section width in millimeters, 70 is sidewall height as a percentage of width, R means radial construction, and 17 is the rim diameter in inches. Overall tire diameter includes the rim and two sidewalls.
One inch is exactly 25.4 mm. This gives nominal geometric diameter, not measured rolling circumference.
For 265/70R17, each sidewall is 265 × 0.70 = 185.5 mm. Diameter is 17 × 25.4 + 2 × 185.5 = 802.8 mm, or about 31.61 inches. In a flotation size such as 33x12.50R15, the first number already gives the nominal overall diameter: 33 inches.
Comparing axle ratios and tire sizes
| Axle ratio | Transmission gear | Tire diameter | Engine RPM |
|---|---|---|---|
| 3.73 | 1.00 | 31 in | 2,629 |
| 4.10 | 1.00 | 31 in | 2,890 |
| 3.73 | 0.70 | 31 in | 1,840 |
| 3.73 | 1.00 | 35 in | 2,328 |
| 4.10 | 1.00 | 35 in | 2,559 |
Changing from 31-inch to 35-inch tires lowers RPM by about 11.4% at unchanged gearing and road speed. Moving from a 3.73 to a 4.10 axle partly offsets that change, but does not restore the original RPM exactly.
Checks before using the result
- 1Use input speed under the intended load. The calculator converts the RPM you enter. A motor's no-load speed may differ from its operating speed.
- 2Combine efficiencies by multiplication. If two stages are each 95% efficient, their combined efficiency is 0.95 × 0.95 = 90.25%. Enter that overall percentage, not 95%.
- 3Separate ratio from component capacity. The torque result does not check tooth strength, shaft loads or thermal limits. A calculated ratio also does not establish whether two physical gears will mesh correctly.
Vehicle results use a circular tire model. Actual rolling circumference varies with tire construction, load, pressure and tread wear; nominal diameter alone cannot capture all of these effects. The speed result also does not account for whether the engine has enough power to reach that speed.
Frequently asked questions
What does a 3:1 gear ratio mean?
The input turns three times for each output turn. Under this page's convention, it is a reduction with one-third the input speed and three times the ideal input torque.
Is a higher gear ratio faster?
At a fixed input RPM, a numerically higher reduction ratio gives a slower output. In a vehicle, it raises engine RPM at the same road speed; ratio alone does not predict acceleration or maximum speed.
Does efficiency change output RPM?
Not in the calculation for fully engaged gears at a specified input RPM. Efficiency changes available output torque, although the real motor's operating RPM may change when its load changes.
What does a 3.73 axle ratio mean?
In straight-line travel, the driveshaft turns 3.73 times for each wheel turn. The transmission gear ratio is separate and multiplies the axle ratio when relating engine RPM to wheel RPM.
Sources
- 1MAE 3: Gear ratios · University of California San Diego · Accessed November 2026
- 2Applied mechanics, 9.4: Gear transmissions · Jönköping University · Accessed November 2026
- 3Michelin tire FAQs: Reading tire sidewall markings · Michelin · Accessed November 2026
- 4MICHELIN Truck Tire Service Manual: Tire revolutions per mile calculation · Michelin · Accessed November 2026
- 5NIST Guide to the SI, Appendix B.9: Conversion factors by quantity · National Institute of Standards and Technology · Accessed November 2026
Estimates are for planning; have a qualified engineer or mechanic check component limits before changing a drivetrain.