How the tire size calculator works
Choose One tire to find a size's nominal width, sidewall height, overall diameter, circumference and estimated revolutions per mile or kilometer. Compare two adds the diameter difference, percentage change, estimated ground-clearance change and speedometer comparison. The original tire is the baseline for percentage changes.
- 1Choose each tire's size format. For a metric size such as 225/65R17, enter width, aspect ratio and wheel diameter. For an inch-based flotation size such as 33x12.50R15, enter overall diameter, width and wheel diameter.
- 2Enter the comparison speed. Use the indicated speed shown on the speedometer. The speed result estimates actual road speed with the new tire, assuming the speedometer was accurate with the original size.
- 3Choose your display units. Read dimensions in inches or millimeters and speed in mph or km/h. Changing display units does not change the underlying tire size.
How to read the tire size
In 225/65R17, 225 is the nominal section width in millimeters, measured from sidewall to sidewall. The aspect ratio, 65, means the sidewall height is 65% of that width. R identifies radial construction, and 17 is the wheel diameter in inches. A leading P identifies a passenger tire; LT identifies a light-truck tire.
Flotation sizes use a different order. In 33x12.50R15, 33 is the nominal overall diameter in inches, 12.50 is the section width in inches, and 15 is the wheel diameter in inches. The first number already includes the wheel and both sidewalls.
Tire diameter and circumference formulas
For a metric tire, first calculate one sidewall's height. Add two sidewalls to the wheel diameter to get overall diameter, then multiply by π to get the geometric circumference.
Wheel means wheel diameter. One inch is exactly 25.4 millimeters.
Divide a millimeter dimension by 25.4 to express it in inches. Estimated revolutions are the travel distance divided by circumference, with both lengths in the same unit.
The distance constants are in millimeters. Results are geometric estimates of tire revolutions.
For a flotation size, use the stated overall diameter directly. Its sidewall height follows from subtracting the wheel diameter and dividing the remainder between the top and bottom sidewalls.
For 33x12.50R15, the calculated sidewall is (33 − 15) ÷ 2 = 9 inches. Overall diameter must exceed wheel diameter.
Comparing diameter, clearance and speed
Use the same length unit for both diameters. Clearance change estimates the change in axle height with all other conditions unchanged.
Actual and indicated speed use the same unit. The original diameter must represent the speedometer's calibration baseline.
A taller tire covers more distance per revolution, so estimated actual speed is higher than indicated speed. A shorter tire produces the opposite result. This calculation assumes accurate original calibration, no recalibration after the change and rolling without slip; it does not correct an existing speedometer error.
Worked example: 225/65R17 versus 235/65R17
Using 225/65R17 as the original size, one sidewall is 225 × 65 ÷ 100 = 146.25 mm. Overall diameter is 17 × 25.4 + 2 × 146.25 = 724.3 mm, or 28.52 inches. The new 235/65R17 size has a 152.75 mm sidewall and a 737.3 mm diameter.
| Measurement | 225/65R17 | 235/65R17 |
|---|---|---|
| Section width | 8.86 in | 9.25 in |
| Sidewall height | 5.76 in | 6.01 in |
| Wheel diameter | 17.00 in | 17.00 in |
| Overall diameter | 28.52 in | 29.03 in |
| Circumference | 89.58 in | 91.19 in |
| Estimated revs per mile | 707 | 695 |
| Estimated revs per km | 439 | 432 |
Diameter increases by 13 mm, or 0.51 inches. Dividing 13 by the original 724.3 mm and multiplying by 100 gives +1.79%. Estimated ground clearance increases by half the diameter difference: 6.5 mm, or 0.26 inches.
| Indicated speed (mph) | Estimated actual speed (mph) |
|---|---|
| 30 | 30.54 |
| 50 | 50.90 |
| 60 | 61.08 |
| 70 | 71.26 |
The same ratio applies in km/h: an indicated 100 km/h becomes an estimated 101.79 km/h. Calculations use unrounded dimensions, so dividing the rounded inch values in the table can give a slightly different result.
What the 3% guideline means
Continental's North American plus-sizing bulletin advises matching original rolling circumference as closely as possible and discusses ±3% as a general guideline under most circumstances. Because geometric circumference is proportional to diameter, the calculator can screen sizes using percentage diameter change. An absolute change of 3% or less is within that comparison band; it is not a fitment approval or a universal safety threshold.
Checks before changing tire size
- 1Start with the vehicle's specified size. NHTSA recommends the original size or another size recommended by the vehicle manufacturer. Check the owner's manual or Tire and Loading Information Label on the driver's door edge or post.
- 2Check the wheel and surrounding clearance. Confirm the tire's approved rim-width range and clearance through full steering movement and suspension travel. The calculated section width does not determine where the tire sits relative to the suspension or fender.
- 3Check ratings separately. Load capacity, speed rating and inflation requirements are outside this dimension calculation. A similar diameter does not establish that a replacement meets those requirements.
- 4Follow AWD and 4WD instructions. The 3% comparison band is not an allowable mismatch between axles. Follow vehicle-specific requirements, including any factory-specified different front and rear sizes.
Why measured tire specifications can differ
The calculation treats the tire as a circle using its nominal size markings. It does not use product-specific measured dimensions or adjust for tread wear, load or inflation. Michelin defines revolutions per mile as a measured value that can vary with speed, load and inflation pressure. Manufacturer rolling data can therefore differ from the geometric estimate, and half the nominal diameter difference is only an estimate of the ground-clearance change.
Frequently asked questions
What does 225/65R17 mean?
It identifies a nominally 225 mm wide radial tire with a sidewall height equal to 65% of its width, fitted to a 17-inch wheel. Its calculated overall diameter is 724.3 mm, or 28.52 inches.
How tall is a 265/70R17 tire?
Its calculated diameter is 802.8 mm, or 31.61 inches. Each sidewall is 265 × 70 ÷ 100 = 185.5 mm, added twice to the 431.8 mm wheel diameter.
Does a bigger wheel always mean a taller tire?
No. A larger wheel can be paired with a shorter sidewall to keep overall tire diameter close to the original. Calculate the complete tire diameter instead of comparing wheel diameters alone.
How many revolutions per mile does a 31-inch tire make?
The geometric estimate is about 651 revolutions per mile: 63,360 ÷ (π × 31). A particular tire's measured revolutions per mile can differ from this estimate.
Can I compare a metric tire size with a flotation size?
Yes. Choose the appropriate format for each tire, such as 265/70R17 for one and 33x12.50R15 for the other. Both are converted to common dimensions before the comparison.
Sources
- 1Michelin FAQs: Tire sizing and sidewall markings · Michelin · Accessed November 2026
- 2NIST Handbook 44, 2026: Appendix C, General Tables of Units of Measurement · National Institute of Standards and Technology · Accessed November 2026
- 3Tire plus-sizing for passenger and light truck vehicles: PSIB 06-03 · Continental Tire North America · Accessed November 2026
- 4Michelin tire glossary · Michelin · Accessed November 2026
- 5TireWise: Tire safety ratings and awareness · National Highway Traffic Safety Administration · Accessed November 2026
Dimensions and speed estimates do not confirm fitment; have size changes checked by a qualified tire professional.