How the board and batten calculator works
Choose Vertical battens for an accent wall, Grid for rectangular panels, or Siding for wide boards with battens covering their joints. Accent-wall results show the clear gap, center-to-center spacing, cut lengths and boards to buy. Siding results show separate purchases for boards and battens.
Measurement menus are linked: choosing a metric or imperial unit switches the other measurements with it. Imperial spacing is displayed to the nearest 1/16 in; metric spacing is displayed to 0.1 cm. Calculations use unrounded dimensions.
Enter the wall and lumber dimensions
- 1Measure the covered rectangle. Enter wall width and height to cover. For an accent wall, include the height occupied by selected top and bottom rails. For siding, enter the siding height.
- 2Choose the layout. For accent walls, enter actual batten width and either an approximate clear gap or a fixed batten count. Grid also needs the number of panel rows. Select no rails, a top rail, or top and bottom rails.
- 3Set the remaining dimensions. More options controls battens at both wall ends, rail width and extra material. Siding instead needs board width, batten width and the gap beneath the battens.
- 4Choose stock length and extra. Stock lengths are 8, 10, 12 or 16 ft, or 2.4, 2.7, 3, 3.6 or 4.8 m. One selection applies throughout. Extra defaults to 10% and can range from 0% to 50%.
How even spacing is calculated
The requested gap is a target. With end battens, the calculator rounds (wall width − batten width) ÷ (target gap + batten width), then adds one, with at least two battens. Without end battens, it rounds (wall width − target gap) ÷ (target gap + batten width), with at least one batten. Count mode uses your entered count directly.
With end battens off, the corner spaces equal the spaces between battens. The calculator rejects layouts with no positive clear gap. Selected rails must leave vertical space, and grid rows must leave positive-height panel openings.
Worked example: the default 12 ft wall
The default vertical layout covers a 12 × 8 ft wall with 3 1/2 in battens, an approximate 16 in gap, battens at both ends and one 3 1/2 in top rail. Stock length is 8 ft, with 10% extra. Cost estimating is off.
- Count: round((144 − 3.5) ÷ (16 + 3.5)) + 1 = 8 battens.
- Clear gap: (144 − 8 × 3.5) ÷ 7 = about 16.57 in, displayed as 16 9/16 in.
- Center spacing: unrounded gap + 3.5 = about 20.07 in, displayed as 20 1/16 in.
- Vertical cut length: 96 − 3.5 = 92 1/2 in, giving 8 pieces at 7 ft 8 1/2 in.
- Top rail: 12 ft, requiring 2 eight-foot boards joined.
- Purchase: 8 boards for the verticals + 2 for the rail = 10 base boards; adding 10% gives 11 eight-foot boards.
The result also shows 73.7 ft of installed trim and 96 ft² of wall area. Installed length excludes the extra allowance. Wall area is width × height, without deductions for openings.
Grid panels and horizontal pieces
Grid keeps the vertical battens continuous between the selected rails. Horizontal pieces fit into each gap. Their count is (panel rows − 1) × gaps. Panel height is the covered height minus the selected rail widths and horizontal batten widths, divided by panel rows. Horizontal battens use the entered batten width; rail width applies only to the boundary rails.
Switching the default example to Grid with three rows adds 14 horizontal pieces. Each opening displays as 16 9/16 × 28 1/2 in. The purchase becomes 15 eight-foot boards, including 10% extra.
Boards to buy and optional costs
For equal-length vertical or grid pieces that fit within stock, the calculator finds how many whole pieces fit per board, then rounds the required stock count up. Longer pieces each receive enough stock lengths for an end-to-end join. Every full-width rail is counted separately.
Board and batten siding quantities
Check the layout before cutting
- 1Mark from one reference. Avoid repeatedly stepping off rounded center spacing. Check intermediate marks and the far-end batten position against the full wall width.
- 2Check obstructions and stock. Compare layouts around outlets, doors and windows before cutting. Try other stock lengths, then check kerf, joints and actual lumber widths against the cut list.
Frequently asked questions
Is batten spacing the gap or center to center?
Gap means the clear opening between adjacent battens. Center-to-center spacing adds one batten width to that opening.
Can I leave a batten off just one end?
The end option applies to both ends together. A layout with a batten at only one end needs a separate manual adjustment.
Can the grid have square panels?
Adjust the batten count and panel rows until the two Each panel dimensions are close. Choosing Grid does not automatically make square openings.
Does the calculator include backing panels or subtract windows?
Accent-wall quantities include trim, not backing sheets. There is no opening deduction, so adjust the cut list and purchasing plan separately for doors and windows.
Sources
- 1PS 20-25: American Softwood Lumber Standard, Table 3 · National Institute of Standards and Technology · Accessed November 2026
- 2Installing Board & Batten Siding · Western Red Cedar Lumber Association · Accessed November 2026
Material quantities are estimates; have a qualified installer check exterior siding and attachment details.